Cards use the selected rifle and the current conditions, and update when they change. Tap a target to load it on the Dashboard. Always check yardages against the posted brief.
Version 56a86325eb · built 2026-11-22 04:22 UTC
Aim at target
—
Waiting for the compass…
Crop one stage
Drag a box around one stage, choose its stage number, then tap Done.
Check zero
Shoot a group of 3 to 5 at your zero distance, aiming at the same point every shot. Take the photo straight on, with the whole target in the frame and good light. A target with 1-inch grid squares lets the app set the scale by itself.
HIP · highest impact probability
Manual wind
Wind speed (mph) Manual
You set the wind: type the speeds here, then close this and drag the wind clock to where the wind comes from.
Meter goes back to your wind meter: it connects to the meter you used last, or opens Settings to scan for one.
Trending
Connect a meter to see the wind graph.
Tap an average to show it on the graph as the dashed line. For reading only: your holds use Live or Manual.
Air
Rifle and scope
Bullet
Muzzle Velocity
Truing
Round counter
Zero and groups
About the solver
Units of measure
Bluetooth
Voice controls
Subscriptions
Misc settings
Mover settings
Goes on your stage scores and shared results. Leave it blank to skip.
Or take a quick tutorial on your own screens:
Walkthrough
About 2 minutes, with captions. Turn the sound on to hear it.
Help topics
Wind
Meters
Rifle and truing
Conditions
Stages and timer
Moving targets
App
Set zero offset
If your rifle's group doesn't land on your aim point at your zero distance and you're not re-zeroing the scope, set the offset here. Every hold for this rifle then corrects for it.
Or enter it by hand
Paste brief text
Your phone's own text reader is the most accurate. iPhone: open the brief photo in Photos, press and hold on the words, tap Select All, then Copy. Android: open it in Google Photos or Lens, tap Text, Select all, Copy. Then paste below.
Stage holds
Circles: hold that mark on the target. A square marks a target your dial is exactly on. Elevation only: hold your wind for each target as you would on the stage card. Movers are shown at their edge lead.
Reticle
Pick your reticle.
Dope card (mil)
| Yds | Elev | Imported | Diff | Wind | Edge lead | Time | Max ord |
|---|
Elev: U up, D down. Wind: hold L or R on a still target. Edge lead: hold ahead of the front edge on a mover (not the center), wind and spin included. Max ord: the bullet's highest point above your line of sight when dialed for that distance, where it peaks, and its angle there in your units.
Compare & true to a dope card
Your card is shown next to the app's own solution, row by row, so you can see where they differ and true the app to your known dope.
1 · The card
A CSV or text export reads best, then a screenshot, then a straight, close photo of just the table.
2 · Check the numbers
| Range | Elevation |
|---|
3 · Conditions printed on the card (optional)
Leave any of these blank and the app assumes standard air: 59 °F, sea level, 29.92 inHg, 0% humidity (and your rifle's zero). If the card was made for different conditions, the truing will be off and you may have to true again at the range. If the card shows only barometric (sea-level) pressure, leave pressure blank and enter the altitude.
4 · Compare and true
Worked out from the rows and conditions above. Nothing changes until you tap Use this truing.
| Range | Card | App | Diff |
|---|
Want a quick tour?
Each one takes a minute and walks you through your own screens. They're always under ? Help.
Dope card increment
How often should the card show a distance? You can change it later from the card.
Search
Help
Live wind and Live air
Which wind the solution uses is the highlighted button under the wind clock: Live · 10 s or Manual. Double-tap one to pick it. The 1 to 10-minute averages are in Trending, for reading only.
Wind typed by hand starts at 0 (12 o'clock) each time the app opens, so an old wind is never left in the solution. Enter today's wind, or connect a meter.
When a meter connects, the solution switches to its 10-second average and Dashboard shows a LIVE tag. The Lowest, Live and Highest wind boxes then show the lowest, average and highest reading in the box you picked, and can't be typed in. Pick Manual to type your own.
If the meter drops (out of range, battery), a red banner says so and the app holds the last wind it had. Reconnect the same meter to go back to the box you had picked; Dismiss goes to Manual with the last readings filled in, so you can set the wind yourself.
Live air works the same way for temperature, humidity and pressure, but only with meters that send them: Kestrel meters, WFPSM BLE meters and standard Environmental Sensing meters. The Calypso sends wind only, so with a Calypso, air comes from Get conditions or what you type. While a meter drives Live air, hourly weather pauses. A WFPSM meter's sensor sits in the airflow, but direct sun on the meter can still read warm.
Wind direction: the Calypso sends direction, so with a Calypso the wind clock follows the meter. WFPSM BLE meters and meters that send speed only don't, so set the direction on the wind clock yourself (touch or drag); the meter gives the speed. Point the WEATHERmeter into the wind.
Share or export
Whole match stages, targets, yardages, briefs and holds setup · no scores, times or photos
Results only
HIP · highest impact probability
Distance used.
What it is. HIP suggests the one wind hold most likely to put a round on the plate when the wind won't sit still. HIP is a tool, not the solution: a shooter aid. It never changes the windage on the Dashboard; that stays the solver's call for the wind you've set.
Why not just hold the average? A bullet is in the air well under two seconds, and gusts last longer than that, so each shot gets either the base wind or a gust, not a blend. HIP holds where the wind spends its time. In gusty wind that's usually a little under the average. In wind that switches sides, the average can sit between the two conditions and miss both; HIP commits to one.
How it works. For every possible hold, HIP adds up the chance of a hit across the whole spread of wind, with your own group spread on top, and shows the hold with the highest total. Drift per mph comes from the solver, so your load, the air, the distance and the shot angle are all included, along with spin drift.
Wind from. With a meter connected and Live picked, HIP uses every reading from the last minute (not just the average), turned into crosswind for your line of fire, to find the hold; it needs about a minute of readings. The brackets and X1 / X3 are the lowest and highest wind of the last 10 minutes (or since you connected or cleared, if that's shorter); X2 is the last minute's average. With Manual (or no meter), HIP spreads the wind from the Lowest wind through the Constant wind to the Highest wind, at the clock direction.
Target width is the plate's width, in MOA or inches (an IPSC or rectangular target: its width at the height you're aiming). The box shows it converted at the current distance. Your group is the size of a typical group from the position you're shooting (off a barricade it's often bigger than off the bench); 1 MOA is a fair start.
Reading the box. HIP hold is the suggested hold, with the wind speed it matches. Hit chance is how often that hold hits, given everything above. Covers is the range of wind that hold still hits in: your error budget. The plate picture (it opens the same way from the Live wind panel on the Dashboard) shows the plate as a square at its real width with the HIP point of aim as a dot, held off the plate, not dialed. The shading runs from the dot to the middle of the plate, on the side to shoot. If the dot is off the plate, the half of the plate on that side is shaded. The two dotted brackets mark the hold for the minimum wind and for the peak wind (hold above, mph below). The X's show where the bullet lands if you hold the HIP hold: X1 in the minimum wind, X2 in the average, X3 in the peak. The X's are stacked one above the other only so they're easy to tell apart; their height isn't a prediction. HIP is about left and right only, so read each X by how far across the plate it sits. A dark X hits; a red X misses, with how far past the edge it lands written above it. The key and the table under the plate repeat these numbers.
When the wind beats the plate. If no hold reaches about 70%, the box turns orange and tells you to wait for your condition, with the hold for the most common wind and the chance if you shoot in it.
Example. 500 yd, 2 MOA plate, 6.5 mm at 2840 fps, wind mostly 5 to 6 mph right to left with gusts to 10 about a third of the time: HIP holds right (into the wind) for about 7 mph, with a hit chance near 97%. Holding for the full 10 mph drops that to about 56%.
Limits. The numbers are only as good as what goes in: your real group size, a meter that's set up pointing at the target and a good read of the wind. Confirm on steel.
Barricade Ballistics Pro
Everything in the app, for every match.
Payment is charged to your Apple ID when the free trial ends, or at purchase if no trial applies. The subscription renews automatically at the same price unless it's canceled at least 24 hours before the current period ends. Manage or cancel in Settings › your name › Subscriptions. Without Pro, the Dashboard, wind and weather, one rifle, and velocity and drag truing stay free.
HIP
| Tgt | Yds | HIP hold | Hit |
|---|
HIP holds for the wind spread (the meter's last minute with the last 10 minutes' lowest and highest, or Manual, on the Conditions tab), on each target's own width and this stage's line of fire. Wind is held, not dialed. The key under the plate explains the marks.
Opened as a copy
Stages · untick any you don't want
Share by QR code
Works with no signal. Pick the stages to send (briefs go with them), then the other phone taps Stages › Load match › Scan a match QR code.
Hold the phones about a foot apart. The codes change on their own until the other phone has all of them.
Scan the match QR code
Point the camera at the other phone's code.
Stage timer
Meter disconnected · holding last wind ()